B&O MCL 2A

B&O MCL 2A – X-TRA Speaker Kit and audio link in the MCL system

The MCL 2A is the most widely used unit in Bang & Olufsen's Master Control Link (MCL) system and represents the classic solution for multi-room audio linking. Often sold under the name X-TRA Speaker Kit , the unit enabled the creation of a link room with passive speakers and full control via the B&O remote control.

The MCL 2A is an audio-based Local Control System (LCS) unit and technically functions as a direct extension of the audio system in the main room.

What is MCL 2A?

The MCL 2A is used to distribute sound from a Bang & Olufsen audio or video system in the main room to one or more link rooms via cable. The system makes it possible to listen to music and TV sound throughout the house with the same user experience and operating logic.

MCL 2A is an analog, wired link system, known for high reliability and simple architecture.

Typical applications of MCL 2A

MCL 2A was typically installed in:

  • bedrooms
  • kitchens
  • offices
  • guest rooms

Here it provided access to the main room's sources without the need for a separate system in the link room.

Connection to the main compartment – ​​MCL cabling

The MCL 2A is connected to the main room via the classic 7-conductor MCL cable in a point-to-point installation. The cable carries:

  • left and right audio channels
  • common frame
  • data signal for control
  • supply voltage

Via this single cable, the MCL 2A receives both audio, control and power from the main system.

Common volume control in MCL 2A

The MCL 2A functions as a direct extension of the audio system in the main room. This means that the volume is shared between the main room and the link room.

When you adjust the volume in the link room, the volume in the main room also changes – and vice versa. This shared volume control is a fundamental part of the MCL 2A's design and at the same time its biggest functional limitation.

The need for independent volume control in link rooms later led to the development of the MCL 2AV.

Passive speakers in MCL 2A installations

The MCL 2A supports passive speakers only . These speakers act as a direct extension of the main room speaker system.

Typical Bang & Olufsen speakers used with the MCL 2A were:

  • Beovox CX 50
  • Beovox CX 100
  • Beovox 300
  • Beovox 5000

MCL 2A has no Powerlinkoutputs and therefore cannot be used with active BeoLab speakers.

Local AUX input for TV and other sources

In addition to access to the main room sources, the MCL 2A has a local AUX input , which allows you to connect a local analog source in the link room.

The AUX input was typically used for:

  • a local TV in the link room
  • other simple audio sources

The sound from the AUX input is played only in the link room and cannot be distributed further in the MCL system. The volume continues to follow the main room volume setting.

IR transceiver and remote control

The MCL 2A uses a separate IR transceiver , which is placed visibly in the link room. The transceiver receives signals from B&O remote controls such as the Beolink 1000.

The transceiver is equipped with:

  • Mute button, which is used for on, off and mute
  • Timer button, which provides access to the main room's timer function, often used as an alarm clock

Via the remote control, the user can select sources and control the volume in the same way as in the main room.

Limitations at MCL 2A

Although MCL 2A was a stable and widely used solution, it has clear limitations:

  • no local volume control in the link room
  • no support for active speakers
  • limited local functionality compared to MCL 2AV

These limitations are important to know when upgrading or troubleshooting.

MCL 2A in Bang & Olufsen's link history

The MCL 2A represents the most widespread and classic version of Bang & Olufsen's early audio link systems. It made multiroom sound possible in a time when digital solutions did not exist, and laid the technical foundation for later systems such as MCL 2AV og Masterlink.