User manual for Neo Avant Kit 55
User manual for the product Neo Avant Kit 55 - which upgrades a Beovision Avant 55″ stand from Bang & Olufsen.
How to mount the Neo Avant Kit 55 on a Beovision Avant stand
Beovision Avant 55″ was a ground-breaking TV from Bang & Olufsen. However, over time, lack of spare parts and high repair costs may make it necessary to upgrade.
The Neo Avant Kit 55 allows you to reuse the iconic motorized stand from the Beovision Avant 55″ with a new TV that has modern functions and apps.
This guide will help you mount the Neo Avant Kit 55, including attaching the bracket and VESA plate, so you can install a new TV on the stand and maintain the exclusive B&O experience.
Contents of Neo Avant Kit 55:
- Bracket for mounting on the Avant 55 stand (4 parts)
- Screws for mounting on the Avant stand (4 pcs.)
- Retaining bracket with 2 screws for fixing the VESA plate on the Neo Avant Kit 55
Assembly steps
1. Remove the old TV from the stand
- Switch off the TV and disconnect the power and signal cables.
- Loosen the screws securing the old TV to the stand.
- Carefully remove the TV and set it aside.
2. Prepare the stand
- Clean the stand and remove any remaining brackets or fasteners from the old TV.
- Check that the stand still works mechanically by testing the rotation.
- Remove the old bracket from the stand and set it aside
3. Mounting the Neo Avant bracket on the Beovision 55″ stand
- Place the Neo Avant 55 bracket on the stand where the previous bracket was attached.
- Use the supplied screws to securely fasten the bracket.
- Make sure the bracket is level before fully tightening the screws.
4. Mounting the VESA plate
- Attach the VESA plate to the new TV.
NOTE – The VESA bracket must be fitted to the TV before it is fitted to the stand - Check that the VESA plate is securely attached and that it fits the Neo Avant bracket.
5. Mounting the new TV on the stand
- Check that the TV is stable and not loose
- Lift the new TV (with the VESA plate attached) and place it on the Neo Avant bracket.
- Attach the TV and the VESA plate to the Neo Avant Kit 55 with the supplied screws and retaining plate.
- Check that the TV is level before tightening the screws
Remove the old bracket from the Beovision Avant
Once you have removed the old B&O Avant 55″ TV from the stand and set it aside, you are ready to remove the suspension bracket for the B&O TV
The old suspension bracket only fits a Bang & Olufsen Avant 55″ TV, so it should no longer be used, but for good measure it makes sense to save it.
Prepare for mounting the Neo Avant Kit 55 on the stand
After removing the original suspension bracket, you are ready to mount the Neo Avant Kit 55. Before you start attaching the new TV, check that the stand is level and that the adjustment screws under the stand are correctly adjusted. Check whether the stand is stable and secure.
Check that you have received the correct parts and that they are ready for assembly on the Avant stand.
Note that the parts must be assembled correctly. There is a rebate and a groove that must fit together. This ensures that the parts are correctly centered and level together.
You are now ready to mount the Neo Avant Kit 55 on the Beovision stand.
Mount the Neo Avant Kit 55 on the Beovision stand
Carefully assemble these 2 items (part no. 1 and 2) and attach them to the stand with a screw.
Install the screw with your fingers and do not tighten completely yet.
Note - you must ensure that the holes in the large block (no. 1) fit the holes in the stand - check this.
Also check that the groove and fold in the large block (no. 1) match the upper part (no. 2)
Mount both screws on the curved top part (no. 2) - but only loosen them by hand so that it is still possible to mount the bottom part.
Then mount the wide plate (no. 3) at the bottom with the 2 screws.
Tighten the screws by hand.
Align parts fully into place so that it fits together and tighten the screws by hand all the way.
Now use a screwdriver and tighten the Neo Avant Kit completely - tighten.
Do not use an electric screwdriver - it will damage the screw head and may damage the Neo Avant Kit brackets
Your Beovision Avant 55″ stand is now ready to mount a VESA bracket - buy it Neo Shop.
Newer TVs have holes on the back of the TV for a VESA plate. The VESA standard describes that the holes must be spaced e.g. 200 mm apart or 300 mm apart. That part is standardized - but then it also stops here.
There are many different makes of TV - eg LG, Samsung, Philips, Loewe, Sony or Panasonic (and many more), so there are many options for placing the VESA holes.
That is why we have created a VESA Guide, which helps you find the right VESA plate for your particular TV and a Beovision Avant 55 stand.
VESA plate together with Neo Avant Kit 55
The VESA plate is here attached to the Neo Avant Kit to illustrate the method and make the method visible.
The VESA plate must be attached to your TV BEFORE you put it on the stand and Neo Avant Kit - otherwise it will be unnecessarily difficult to attach the TV to the VESA plate.
Read here how to attach the VESA plate to your new TV
Attach the VESA bracket to the Beovision Avant stand
The last steps are VERY important!
TV with VESA plate must be attached to the Neo Avant Kit in a secure way so that the TV does not fall off during daily use.
This is done with a retaining plate (no. 4 - see picture above).
The plate is fastened with 2 screws and it sits between the VESA plate and the TV.
In the pictures below, this is shown without the TV, which makes it easier to show the practical installation.
When the TV and VESA plate are clamped together, it takes some time to mount it. Do it carefully.
- Insert the screw back into the bracket (no. 3) from behind and through the hole in the VESA plate.
- Grasp the Retaining Plate (no. 4) with one hand and hold it in front of the hole
- Tighten the screw from behind with a screwdriver so that the screw catches the thread of the Retaining Plate (no. 4)
- Do not tighten it completely, but leave it loose
- Now you have to attach the hanger on the other side – it's not quite easy when the TV is on
- Use a wooden stick, a wooden ruler or the end of a ruler to push the Retaining Plate (No. 4) all the way up in front of the second hole
- Fit the screw in the other side
- Before you tighten both screws, check that the TV is level with a spirit level
- Tighten both screws securely
- Now you are done and your TV is completely fixed and secure
Read more about Beovision Avant 55″ here